Board Features

The key features with the ASRock Z170 Extreme7+ are the three M.2 slots that run in PCIe 3.0 x4 mode, and sit in-between the PCIe slots. I want to draw attention to ASRock’s picture with three SSD 750 drives using U.2 adaptors:

When we previously tested the SSD 750, it was noted that when the M.2 to U.2 adaptor was fitted to the motherboard, any double-slot graphics card that used the area near the second PCIe slot to place a long heatpipe going to the far end of the card (such as the GTX 770 Lightning we were using) was unable to be used in the slot above. In this instance, if you wanted to use three of these drives, then GPUs would have to be in the second long PCIe slot or the last slot on the board, which would remove SLI compatibility. So if this is a configuration you might be thinking of, then check your graphics cards can actually fit in the top slot. Some motherboards are starting to be released with U.2 ports where the SATA ports are, which solves the problem.

ASRock Z170 Extreme7+
Warranty Period 3 Years
Product Page Link
Price Amazon US
Size ATX
CPU Interface LGA1151
Chipset Intel Z170
Memory Slots (DDR4) Four DDR4, Supporting 64GB, Dual Channel, Up to 3600 MHz
Memory Slots (DDR3L) None
Video Outputs HDMI
Network Connectivity Intel I219-V
Intel I211-AT
Onboard Audio Realtek ALC1150
PCIe Slots for Graphics (from CPU) 3 x PCIe 3.0 (x16, x8/x8, x8/x4/x4) - PCIe 2/4/6
PCIe Slots for Other (from PCH) 1 x PCIe 3.0 x4 (PCIe 3)
1 x PCIe 3.0 x1 (PCIe 5)
1 x PCIe 2.0 x1 (PCIe 1)
1 x Half-Height Mini-PCIe
Onboard SATA Six from Chipset, RAID 0/1/5/10
Four from ASM1061
Onboard SATA Express Three, RAID (shares with M.2)
Onboard M.2 3 x PCIe 3.0 x4 or SATA, RAID 0/1, NVMe
Onboard U.2 None
USB 3.1 1 x Type-A + 1 x Type-C (ASMedia ASM1142)
USB 3.1 Front Panel bundled, 1xA + 1xC via SATA Express
USB 3.0 4 x Rear Panel (Z170)
4 via headers (ASM 1074 hub)
USB 2.0 2 x Rear Panel
6 via headers
Power Connectors 1 x 24-pin ATX
1 x 8-pin CPU
Fan Headers 2 x CPU (4-pin)
4 x CHA/SYS (4-pin)
IO Panel 1 x Combination PS/2
2 x USB 2.0
4 x USB 3.0
1 x USB 3.1 Type-A
1 x USB 3.1 Type-C
2 x Network RJ-45
Audio Jacks
Other Features Thunderbolt Header
Power/Reset Buttons
TPM Header
Two-Digit Debug Display
Clear CMOS Button
BIOS Selection Switch
Front Panel Header
Front Audio Header
COM Header

Rather than continually ranting on about M.2 to U.2, the rest of the motherboard gives dual Intel network ports (I219-V and I211-AT), an enhanced Realtek ALC1150 audio codec solution, two USB 3.1 ports on the rear, a total of eight USB 3.0 ports (four on rear from the chipset, two headers onboard from a hub) and six fan headers all-in.

In The Box

We get the following:

Driver DVD
User Manual
Rear IO Shield
2-way SLI Bridge
USB 3.1 Front Panel
SATA Express Cable
USB 2.0 Header Cable (for panel)
Four SATA Cables

The USB 3.1 front panel is going to be the biggest thing to notice, followed closely by the SATA Express and USB 2.0 header cables needed to connect it together. Only one SLI bridge is included, presumably to keep costs low. As this is not a gaming branded board, we don’t see any extra Fatal1ty gubbins to entice end-users usually associated with that brand.

Visual Inspection

When taking the motherboard out of the box, it certainly feels like it has a good amount of mass compared to some flimsy alternatives. That mass is visible by looking at the board, showing a 12+2 power delivery with connected heatsinks on two sides of the socket and a rear panel shield stretching from top to bottom to provide both an aesthetic and an EMI shield. The chipset heatsink is also large compared to some others, used for a number of controllers underneath, and the styling continues using non-horizontal lines.

The PCB itself looks fairly busy, a common trait of ASRock boards, although it is clear that ASRock is using a decent quality board. The Extreme7+ is built for casual and prosumers in mind, hence we see relatively few onboard options for overclocking or extreme overclocking, but there are power and reset buttons in the top right for quick and dirty power management, and a two-digit debug on the bottom of the board for error codes.

The socket has all six 4-pin fan headers within easy reach – one in each corner of the socket (CPU_1 on the top left, CPU_2 on the top right), with another on the top right of the board next to the DRAM and another below the USB 3.0 headers on the right and in the middle of the board.

Moving counter clockwise, below the 24-pin ATX connector are two USB 3.0 headers powered by an ASMedia hub, so it is worth noting that bandwidth will be shared between these headers. On the SATA side of things there are two SATA Express ports in a regular position, featuring four of the SATA ports as well. This is followed by four SATA ports from an ASMedia ASM1061 controller, and then coming out of the motherboard is another SATA Express port containing two SATA ports, making ten SATA ports in total.

On the bottom of the board, from right to left, is an open USB 2.0 header, two closed off USB 2.0 headers (can be used for the USB 3.1 front panel), the two-digit debug display, the front panel header, the two BIOS chips, a BIOS select switch, a ClearCMOS header, a TPM header, the COM header, and finally the front audio header.

Now we come to the Eton Mess of ‘where are those PCIe lanes’ in the middle of the board. We have a mix of PCIe slots from the processor, PCIe slots from the chipset, M.2 slots from the chipset, and a mini-PCIe to add a cherry on top.  Here’s a poorly drawn diagram drawn by my cat in MSPaint:

Here, the gray PCIe slots are from the CPU and are designed for graphics cards or high performance co-processors that need a PCIe x8 link or above. The slots in black (x1, x4, mini-PCIe and the open-ended x1 near the bottom) are from the Z170 chipset. The Ultra M.2 slots in blue, capable of a PCIe 3.0 x4 link and are Intel RST capable, are also from the chipset. Exact configurations of what works when (especially when SATA Express is in the mix) are found in the manual. To the left of the PCIe slots is the bottom part of the IO shield, which acts as a secondary EMI shield for the enhanced Realtek ALC1150 audio solution.

On the rear panel, by virtue of moving any BIOS buttons away, there are a healthy number of other features here. Two USB 2.0 ports along with four USB 3.0 ports, but in the middle is a USB 3.1 combination plinth with a Type-A and Type-C port in tow, both of which are powered by an ASMedia ASM1142 controller. For legacy we have a combination PS/2 port on the bottom left, and video outputs come via HDMI, DP1.2 and DVI-D ports. The two Intel network ports are also present, and at the end are the audio jacks.

Test Setup

Test Setup
Processor Intel Core i7-6700K (ES, Retail Stepping), 91W, $350
4 Cores, 8 Threads, 4.0 GHz (4.2 GHz Turbo)
Motherboards ASRock Z170 Extreme7+
Cooling Cooler Master Nepton 140XL
Power Supply OCZ 1250W Gold ZX Series
Corsair AX1200i Platinum PSU
Memory Corsair DDR4-2133 C15 2x8 GB 1.2V or
G.Skill Ripjaws 4 DDR4-2133 C15 2x8 GB 1.2V
Memory Settings JEDEC @ 2133
Video Cards ASUS GTX 980 Strix 4GB
MSI GTX 770 Lightning 2GB (1150/1202 Boost)
ASUS R7 240 2GB
Hard Drive Crucial MX200 1TB
Optical Drive LG GH22NS50
Case Open Test Bed
Operating System Windows 7 64-bit SP1

Readers of our motherboard review section will have noted the trend in modern motherboards to implement a form of MultiCore Enhancement / Acceleration / Turbo (read our report here) on their motherboards. This does several things, including better benchmark results at stock settings (not entirely needed if overclocking is an end-user goal) at the expense of heat and temperature. It also gives in essence an automatic overclock which may be against what the user wants. Our testing methodology is ‘out-of-the-box’, with the latest public BIOS installed and XMP enabled, and thus subject to the whims of this feature. It is ultimately up to the motherboard manufacturer to take this risk – and manufacturers taking risks in the setup is something they do on every product (think C-state settings, USB priority, DPC Latency / monitoring priority, overriding memory sub-timings at JEDEC). Processor speed change is part of that risk, and ultimately if no overclocking is planned, some motherboards will affect how fast that shiny new processor goes and can be an important factor in the system build.

For reference, the ASRock Z170 Extreme7, on our testing BIOS 1.4, MCT was not enabled by default. Also, the FCLK 10x ratio was not present in the BIOS at the time of testing, but is available on the newest BIOSes.

Many thanks to...

We must thank the following companies for kindly providing hardware for our test bed:

Thank you to AMD for providing us with the R9 290X 4GB GPUs.
Thank you to ASUS for providing us with GTX 980 Strix GPUs and the R7 240 DDR3 GPU.
Thank you to ASRock and ASUS for providing us with some IO testing kit.
Thank you to Cooler Master for providing us with Nepton 140XL CLCs.
Thank you to Corsair for providing us with an AX1200i PSU.
Thank you to Crucial for providing us with MX200 SSDs.
Thank you to G.Skill and Corsair for providing us with memory.
Thank you to MSI for providing us with the GTX 770 Lightning GPUs.
Thank you to OCZ for providing us with PSUs.
Thank you to Rosewill for providing us with PSUs and RK-9100 keyboards.

ASRock Z170 Extreme7+ Overview and Feature Comparison BIOS


View All Comments

  • ghostmuse - Monday, November 30, 2015 - link

    I haven't used this particular piece of software before, but it says it has been updated for Windows 10. Hopefully that = accurate readings. Reply
  • hubick - Friday, November 27, 2015 - link

    No 10GBASE-T? :( Reply
  • extide - Monday, November 30, 2015 - link

    Not Extreme 11 Reply
  • msrt - Friday, November 27, 2015 - link

    Another pro audio user here.
    Are you sure those DPC values are caused by the BIOS and not the wireless drivers?

    On the DPC slide both boards above 200us have WIFI onboard, the others don't.

    With my quite old system I have to use streaming mode through WLAN optimizer or disable WIFI altogether to get rid of DPC spikes. Steady 60-80us vs. the frequent 300us spike.

    Maybe it's the same issue with these (The MSI G1 and this one).
    Ian, could you post an average DPC number or have a quick look with WIFI disabled?
  • Byte - Saturday, November 28, 2015 - link

    This board does not come with Wifi, but has a mPCIe for it and some holes Reply
  • alyarb - Friday, November 27, 2015 - link

    I clicked on this because I wanted to see 3 nvme drives in RAID-0. It's in the title and you post a picture of such a setup on page 1, but I don't see any storage testing besides USB file copy? Reply
  • OFelix - Friday, November 27, 2015 - link

    "The UEFI Tech Service is this weird idea for ASRock to receive submissions about BIOS errors and issues. I’m not sure if ASRock actually answers any of these, or if it is just used as an internal metric to move certain issues up the priority chain."

    I reported a problem last week and got a response from Taiwan in a couple of days.
  • npz - Saturday, November 28, 2015 - link

    I'm surprised. Very cool Reply
  • DanNeely - Friday, November 27, 2015 - link

    Is the USB 3.1 front panel adapter something that could be used to salvage the worthless SataExpress ports on any motherboard; or did asrock have to do anything special on the board to make it work? Reply
  • pedjache - Saturday, November 28, 2015 - link

    As pictured, speical stuff is on the board of the panel, not the mobo. You use 'normal' SATA express, usb2.0 and molex. Wonder if(when) they or anyone else will put up just the front panel on sale. Reply

Log in

Don't have an account? Sign up now